How to Remove Water Heater Sediment

How to Remove Water Heater Sediment
August 16, 2013 Admin
How to Remove Water Heater Sediment

How to Remove Water Heater Sediment

When water is warmed, naturally occurring minerals separate and settle at the bottom of a water heating system. Gradually, the sediment builds up, reducing the effectiveness of the unit in heating and saving water that could possibly harming the water heater.

Although this occurs in every water heating unit and with any sort of type of water, it takes place more promptly with hard water, which includes a higher concentration of natural minerals. In order to keep your water heating system in proper working order, it is vital to eliminate sediments and contamination from time to time.

Draining your gas water heater and treating it with a cleaner is the best way to dissolve the sediment and keep your unit running at its best. There are separate ways for removing sediments in Gas Water Heater and Electric Gas Water Heater. water heater sediments

For electric units, you’ll have to use a flushing method to dissolve the sediment while for Gas Water Heater you start unplug the electrical cord then shut off the cold water valve.

One of the key benefits of removing water heater sediments is that it assures a long life and consistently reliable operation of your water heater. By removing sediments it will increase the water storage capacity of the heater back to or very near its original dimensions and helps improve the efficiency of the equipment. And lastly, can help you save money in energy costs and water consumption. Have a frequent check up of your water heater monthly or annually.

Things You Will Need

  • Large bucket

  • Garden hose

  • Funnel

  • Residential water heater cleaner

  • Water softenerremoving water heater sediments

Gas Water Heater

1. First, locate the cool water supply line on your unit and turn the valve deal with counterclockwise (left) until it joins the off placement position. Locate the shutoff valve to the gas line for the unit and turn it off. Hang around about 20 to 30 mins for your water heater to cool off. Turn off the gas valve or unplug the electrical cord, and shut off the cold water valve.

2. Next, attach a long garden hose to the drainpipe at the foundation of the water heating system; the hose affixes in the same way it hooks up to the hose bib on the outside of your residence. Place the other end of the hose in a tub if nearby, run it outside or place the end in a large container.

3. After that you open the drain pipe valve on your hot water heating system and afterwards turn the warm water on completely in one or more faucets in your home. Hang around till there disappears water appearing of completion of the hose or your tap.

4. Close the drain valve then detach the water line from the top of the tank, putting a channel in the opening. Pour clean water to your water heating system through the funnel based on the size of your heating system and the cleansing product's directions. For a 40-gallon tank, you will typically pour 2 gallons of tidy water into the storage tank and then combine an added 2 gallons of water with the cleaner. Pour this mix via the channel.

5. Open the gas line and relight the pilot light. Set the thermostat on your container to 120 levels Fahrenheit and let this option rest for 2 hrs or the time suggested by the supplier of the cleaner.

6. Remove the funnel and reattach the water line. Turn off the burner. Open the cold-water valve and the drain valve, which should still be attached to the hose, simultaneously and drain the solution out of your water heater. Let the water run through the tank with the drain valve still open for 10 to 15 minutes to flush everything out and after that you close the drain valve, remove the hose and let your water heater refill.

Take out the channel and reattach the water line. Turn off the burner. Open up the cold-water valve and the drainpipe valve, which should still be affixed to the hose, simultaneously and drain the solution out of your water heating system. Allow the water run through the tank with the drain valve still open for 10 to 15 minutes to purge everything out  and afterward you close the drain valve, eliminate the hose and let your water heater refill.

7. Have a professional install a water softener in your house if you have tough water. This will certainly dissolve numerous of the minerals present in hard water, prolonging the quantity of time you can go between flushing and cleaning your water heater.

Electric Water Heater

1. For electric water heaters, turn off first the breaker to your water heater and then turn off the water supply. Wait for 20 to 30 minutes for the water in the unit to cool down.

2. Next, attach a garden hose to the drain valve at the base of the unit, and run the other end of the hose outside, into a large bucket or into a nearby tub. Slightly open a nearby hot water faucet in the home. Then open the drain valve and let all of the water drain out of your water heater.

3. Afterwards, turn on the cold water supply with the garden hose still attached and the drain valve open. Let water run through the unit to clear out any sediment. When the water coming out of the end of the hose is clear, the unit is clean.

4. Finally, shut the drain valve and remove the hose. Wait an hour or so for the unit to refill before trying to use the hot water.

 

Comments (0)

Leave a reply

Your email address will not be published. Required fields are marked *

*